# Options file for ipppd.
# ipppd will not read /etc/ppp/options or /etc/ppp/ioptions or any other
# config file. Everything has to be in here.

# REMOVE the next line once configuration is complete #########################
# REMOVE the above line once configuration is complete ########################

# "peer" is the name for our syncppp partner.

# STANDARD OPTIONS

debug			# enable debugging
#kdebug X		# set kernel debugging level to X
#nodetach		# (no) fork to the background
#callback X		# ask for callback (parameter X ?)
#lock			# create a lock file for device 
#domain X		# add domain X to a given hostname
#pidfile X		# save pid in file X
#call X			# take options from privileges file (???)
#idle X			# idle time limit (seconds)
#holdoff X		# holdoff time limit (seconds)
#maxconnect X		# set maximum connection time (in seconds ?)
#+mp			# enable multi line ppp
#+pwlog			# log password (WARNING: possible security hole)
#nomagic		# magic number negotiation

# ppp handshake : tuning

#silent			# don't even try to initiate the connection
#passive		# wait for the peer to initiate the connection
#lcp-echo-failure X	# consecutive echo failures
#lcp-echo-interval X	# time for lcp echo events 
lcp-restart 1		# Set timeout for LCP 
#lcp-max-terminate X	# Set max #xmits for term-reqs
#lcp-max-configure X	# Set max #xmits for conf-reqs 
#lcp-max-failure X 	# Set max #conf-naks for LCP


# AUTHENTICATION

#name X			# set local name for auth XXX_
user LOGIN-NAME		# set name for auth with peer; default is value for name
#usehostname		# use hostname for auth
remotename INTERNET   	# set remote name for auth
noauth			# (dont) require peer (the other) to auth
#require-pap		# allow only pap authentication (dialin only)
#require-chap		# allow only chap authentication (dialin only)
#login			# use system password database for pap
#papcrypt		# pap passwords are encrypted

# AUTHENTICATION TUNING
#pap-restart X		# Set retransmit timeout for PAP 
#pap-max-authreq X	# Set max #xmits for auth-reqs
#pap-timeout X		# Set time limit for peer PAP auth.
#chap-restart X 	# Set timeout for CHAP 
#chap-max-challenge X 	# Set max #xmits for challenge 
#chap-interval X 	# Set interval for rechallenge

# COMPRESSION

#noaccomp		# address compression on/off
#nopcomp		# protocol field compression on/off
#novj			# van jacobsen compression on/off
#novjccomp		# van jacobsen connection-ID compression on/off
#vj-max-slots X		# tune maximum vj header slots
#nobsdcomp		# bsd compression on/off
#nodeflate		# deflate compression on/off
#nopredictor1		# predictor1 compression in/off
#noccp			# compression negotation on/off
nolzs			# LZS compression off (not yet supported fully)


# IP NETWORKING

#noip			# en/disable ip transfer
#X:Y			# set local ip to X, remote ip to Y
noipdefault		# don't use name for default ip addr
#useifip		# use ip addresses form interface
#usefirstip		# use first ip from auth file for remote
#netmask 255.255.255.255	# set netmask, 255.255.255.255 is for pointopoint
defaultroute 		# (dont) set default route 
nohostroute		# dont set host route
#noproxyarp		# (dont) set an proxy arp entry
#mru X			# set maximum size of recive units to X
#default-mru		# disable mru negotation
mtu 1500 		# set maximum size of transmit units to X (1500 is OK)
#useifmtu		# use mtu from interface
#ipparam X		# set ip parameters in script X
#ms-dns X		# dns address for the peers use (dialin only)
#ms-wins X		# wins address for the peers use (dialin only)
#ms-get-dns		# accept peers suggestion of dns address (dialout)
#set_userip 		# define valid ip addresses in /etc/ppp/useriptab


#ipcp-restart X		# Set timeout for IPCP 
#ipcp-max-terminate X	# Set max #xmits for term-reqs 
#ipcp-max-configure X	# Set max #xmits for conf-reqs 
#ipcp-max-failure X	# Set max #conf-naks for IPCP 
ipcp-accept-local	# Accept peer's address for us 
ipcp-accept-remote	# Accept peer's address for it 

# IPX NETWORKING

noipx			# en/disable ipx
#ipx-network X 		# IPX network number 
#ipxcp-accept-network	#  Accept peer netowrk
#ipx-node X 		# IPX node number 
#ipxcp-accept-local	# Accept our address 
#ipxcp-accept-remote	# Accept peer's address
#ipx-routing X		# IPX routing proto number 
#ipx-router-name X	# IPX router name
#ipxcp-restart X 	# Set timeout for IPXCP 
#ipxcp-max-terminate X	# max #xmits for term-reqs 
#ipxcp-max-configure X	# max #xmits for conf-reqs 
#ipxcp-max-failure X	# max #conf-naks for IPXCP